AWLGRIP AWL-BRITE CLEAR URETHANE FOR BRIGHTWORK -
PART "A" ONLY AWL-BRITE is a new buffable, higher build, three component low VOC clear urethane for marine brightwork. AWL-BRITE provides a far more durable finish than varnish, is faster curing and is easy to apply. Above the waterline only. Refer to the Brightwork Systems pages in the Awlgrip Application Guide, Edition 12. Product is sold by the quart or gallon.
SPECIFICATION DATA
Type: Three Component Acrylic Urethane
Color: Clear
Theoretical Coverage - Sq. Feet/Gallon; 930 Sq. Feet (86m2) at 1 mil dry (25 microns); 93 Sq. Feet (8.6m2) at recommended dry film thickness of 10 coats. Coverage calculations are based on theoretical transfer efficiency of 100%. Actual coverage rate obtained will vary according to equipment choice, application techniques, part size, and application environment.
Recommended Wet Film Thickness: 2.0-2.5 mils (50-62 microns) per coat.
Recommended Dry Film Thickness: 1.0-1.2 mils (25-30 microns) per coat.
Anticipated Cure Time at 77°F (25°C) /50% R.H: 3 ho urs to recoat; 12 hours to light service; 7 days for full cure.
Recoatability: With itself: 3 hours minimum, 36 hours maximum without sanding or scuffing.
VOC: Base (J3005) – 372 g/lt or 3.1 lbs/gallon
Converter (J3006) – 146 g/lt or 1.2 lbs/gallon
SURFACE PREPARATION
The wood should be clean, dry, smooth, and well seasoned.
Warning: Wood should have no more than 15% moisture content.
New / Bare Wood: AWL-BRITE should only be applied over properly prepared AWL®SPAR (M3131) or AWL-SPAR H.S. (M3146) as part of the Ultimate Brightwork System. Do not apply AWL-BRITE directly to bare wood.
Old Finishes: Old finishes in good condition should be washed with AWL-PREP Surface Cleaner, then sanded with 220-320 grit paper to remove the gloss. Old finishes in poor condition should be removed. Test on a small area to make sure AWL-BRITE CLEAR doesn’t attack the old finish. If old finish is attacked, it must be completely removed before applying the Ultimate Brightwork System.
Interior Applications: AWL-BRITE should only be applied over properly prepared AWL-SPAR (M3131) or AWL-SPAR H.S. (M3146), or QUIK-FIL (J3901/J3902). Do not apply AWL-BRITE directly to bare wood.
Note: Due to the wide variety of substrates, surface preparations, application methods and environments, customers should test the complete system for adhesion and compatibility under their conditions prior to full scale application.
MIXING & REDUCTION
Brush: AWL-BRITE CLEAR is a three component product. Mix by volume 2 parts J3005 with 1 part J3006 until one smooth, homogenous mixture is obtained. Then add ½ part A0031. Overall mix is 2:1:½ by volume. Example: 4 oz. J3005, 2 oz. J3006, 1 oz. A0031. Additional A0031 can be added if desired, but standard 2:1: ½ ratio is required.
Spray: Mix by volume 2 parts J3005 with 1 part J3006 until one smooth, homogenous mix is obtained. Then add ¾ - 1 part A0001 (standard) or A0006 (cool temperatures) Activator.
Mix and use small quantities of AWL-BRITE CLEAR at a time. Keep the original containers closed when not in use. Do not shake AWLBRITE CLEAR. Do not use Pro-Cure Accelerators.
Induction Time after Mixing: None
Anticipated Pot Life at 77°F(25°C), 50% R.H: 1 to 2 Hours
APPLICATION INSTRUCTIONS
General: The key to performance of any varnish system is applying enough material. This is especially true with AWL-BRITE CLEAR Urethane.
These directions call for more coats than are needed to achieve basic cosmetic qualities. If you stop the system when it looks good, or sand excessively, you will not achieve the desired performance.
General: Apply light, smooth coats. Apply two coats in an 8 hour period. Allow to cure 8-12 hours or overnight and repeat. Ten coats are recommended.
Sand as little as possible. Sanding is only required when:
Runs, sags or brush marks need to be leveled.
Dirt or grit needs to be removed from the surface.
If it has been more than 36 hours since the last application.
If no leveling is required, but it has been more than 36 hours since the last application; dulling the surface with Scotchbrite® Pads is recommended, see the application guide for systems. If possible, avoid applying or curing the material in direct sunlight. Do not apply or attempt to cure AWL-BRITE CLEAR below 65°F (18°C ) or over 95°F (35°C).
SHIPPING NOTE: Item may be considered hazardous to ship.
LINKS: To view the PDS sheet for AWLGRIP J3005: CLICK HERE
To view the MSDS sheet for AWLGRIP J3005: CLICK HERE